This change drops TCP packets with a non-unicast IP address as the source or
destination address as TCP is meant for communication between two endpoints.
Test: Make sure that if the source or destination address contains a non-unicast
address, no TCP packet is sent in response and the packet is dropped.
PiperOrigin-RevId: 280073731
This change allows the netstack to do NDP's Prefix Discovery as outlined by
RFC 4861 section 6.3.4. If configured to do so, when a new on-link prefix is
discovered, the routing table will be updated with a device route through
the nic the RA arrived at. Likewise, when such a prefix gets invalidated, the
device route will be removed.
Note, this change will not break existing uses of netstack as the default
configuration for the stack options is set in such a way that Prefix Discovery
will not be performed. See `stack.Options` and `stack.NDPConfigurations` for
more details.
This change reuses 1 option and introduces a new one that is required to take
advantage of Prefix Discovery, all available under NDPConfigurations:
- HandleRAs: Whether or not NDP RAs are processes
- DiscoverOnLinkPrefixes: Whether or not Prefix Discovery is performed (new)
Another note: for a NIC to process Prefix Information options (in Router
Advertisements), it must not be a router itself. Currently the netstack does not
have per-interface routing configuration; the routing/forwarding configuration
is controlled stack-wide. Therefore, if the stack is configured to enable
forwarding/routing, no router Advertisements (and by extension the Prefix
Information options) will be processed.
Tests: Unittest to make sure that Prefix Discovery and updates to the routing
table only occur if explicitly configured to do so. Unittest to make sure at
max stack.MaxDiscoveredOnLinkPrefixes discovered on-link prefixes are
remembered.
PiperOrigin-RevId: 280049278
* Basic tests for the SO_REUSEADDR and SO_REUSEPORT options.
* SO_REUSEADDR functional tests for TCP and UDP.
* SO_REUSEADDR and SO_REUSEPORT interaction tests for UDP.
* Stubbed support for UDP getsockopt(SO_REUSEADDR).
PiperOrigin-RevId: 280049265
This change adds explicit support for honoring the 2MSL timeout
for sockets in TIME_WAIT state. It also adds support for the
TCP_LINGER2 option that allows modification of the FIN_WAIT2
state timeout duration for a given socket.
It also adds an option to modify the Stack wide TIME_WAIT timeout
but this is only for testing. On Linux this is fixed at 60s.
Further, we also now correctly process RST's in CLOSE_WAIT and
close the socket similar to linux without moving it to error
state.
We also now handle SYN in ESTABLISHED state as per
RFC5961#section-4.1. Earlier we would just drop these SYNs.
Which can result in some tests that pass on linux to fail on
gVisor.
Netstack now honors TIME_WAIT correctly as well as handles the
following cases correctly.
- TCP RSTs in TIME_WAIT are ignored.
- A duplicate TCP FIN during TIME_WAIT extends the TIME_WAIT
and a dup ACK is sent in response to the FIN as the dup FIN
indicates potential loss of the original final ACK.
- An out of order segment during TIME_WAIT generates a dup ACK.
- A new SYN w/ a sequence number > the highest sequence number
in the previous connection closes the TIME_WAIT early and
opens a new connection.
Further to make the SYN case work correctly the ISN (Initial
Sequence Number) generation for Netstack has been updated to
be as per RFC. Its not a pure random number anymore and follows
the recommendation in https://tools.ietf.org/html/rfc6528#page-3.
The current hash used is not a cryptographically secure hash
function. A separate change will update the hash function used
to Siphash similar to what is used in Linux.
PiperOrigin-RevId: 279106406
This change allows the netstack to do NDP's Router Discovery as outlined by
RFC 4861 section 6.3.4.
Note, this change will not break existing uses of netstack as the default
configuration for the stack options is set in such a way that Router Discovery
will not be performed. See `stack.Options` and `stack.NDPConfigurations` for
more details.
This change introduces 2 options required to take advantage of Router Discovery,
all available under NDPConfigurations:
- HandleRAs: Whether or not NDP RAs are processes
- DiscoverDefaultRouters: Whether or not Router Discovery is performed
Another note: for a NIC to process Router Advertisements, it must not be a
router itself. Currently the netstack does not have per-interface routing
configuration; the routing/forwarding configuration is controlled stack-wide.
Therefore, if the stack is configured to enable forwarding/routing, no Router
Advertisements will be processed.
Tests: Unittest to make sure that Router Discovery and updates to the routing
table only occur if explicitly configured to do so. Unittest to make sure at
max stack.MaxDiscoveredDefaultRouters discovered default routers are remembered.
PiperOrigin-RevId: 278965143
This change better follows what is outlined in RFC 793 section 3.4 figure 12
where a listening socket should not accept a SYN-ACK segment in response to a
(potentially) old SYN segment.
Tests: Test that checks the TCP RST segment sent in response to a TCP SYN-ACK
segment received on a listening TCP endpoint.
PiperOrigin-RevId: 278893114
This change validates incoming NDP Router Advertisements as per RFC 4861 section
6.1.2. It also includes the skeleton to handle Router Advertiements that arrive
on some NIC.
Tests: Unittest to make sure only valid NDP Router Advertisements are received/
not dropped.
PiperOrigin-RevId: 278891972
When VectorisedViews were passed up the stack from packet_dispatchers, we were
passing a sub-slice of the dispatcher's views fields. The dispatchers then
immediately set those views to nil.
This wasn't caught before because every implementer copied the data in these
views before returning.
PiperOrigin-RevId: 277615351
In the future this will replace DanglingEndpoints. DanglingEndpoints must be
kept for now due to issues with save/restore.
This is arguably a cleaner design and allows the stack to know which transport
endpoints might still be using its link endpoints.
Updates #837
PiperOrigin-RevId: 277386633
This change helps support iterating over an NDP options buffer so that
implementations can handle all the NDP options present in an NDP packet.
Note, this change does not yet actually handle these options, it just provides
the tools to do so (in preparation for NDP's Prefix, Parameter, and a complete
implementation of Neighbor Discovery).
Tests: Unittests to make sure we can iterate over a valid NDP options buffer
that may contain multiple options. Also tests to check an iterator before
using it to see if the NDP options buffer is malformed.
PiperOrigin-RevId: 277312487
This change supports using a user supplied TCP MSS for new active TCP
connections. Note, the user supplied MSS must be less than or equal to the
maximum possible MSS for a TCP connection's route. If it is greater than the
maximum possible MSS, the maximum possible MSS will be used as the connection's
MSS instead.
This change does not use this user supplied MSS for connections accepted from
listening sockets - that will come in a later change.
Test: Test that outgoing TCP SYN segments contain a TCP MSS option with the user
supplied MSS if it is not greater than the maximum possible MSS for the route.
PiperOrigin-RevId: 277185125
This change validates the ICMPv6 checksum field before further processing an
ICMPv6 packet.
Tests: Unittests to make sure that only ICMPv6 packets with a valid checksum
are accepted/processed. Existing tests using checker.ICMPv6 now also check the
ICMPv6 checksum field.
PiperOrigin-RevId: 276779148
This change is in preparation for NDP Prefix Discovery and SLAAC where the stack
will need to handle NDP Prefix Information options.
Tests: Test that given an NDP Prefix Information option buffer, correct values
are returned by the field getters.
PiperOrigin-RevId: 276594592
The amss field in the tcpip.tcp.handshake was not used anywhere. Removed it to
not cause confusion with the amss field in the tcpip.tcp.endpoint struct, which
was documented to be used (and is actually being used) for the same purpose.
PiperOrigin-RevId: 276577088
This change makes it so that NDP work is done using the per-interface NDP
configurations instead of the stack-wide default NDP configurations to correctly
implement RFC 4861 section 6.3.2 (note here, a host is a single NIC operating
as a host device), and RFC 4862 section 5.1.
Test: Test that we can set NDP configurations on a per-interface basis without
affecting the configurations of other interfaces or the stack-wide default. Also
make sure that after the configurations are updated, the updated configurations
are used for NDP processes (e.g. Duplicate Address Detection).
PiperOrigin-RevId: 276525661
This change introduces a new interface, stack.NDPDispatcher. It can be
implemented by the netstack integrator to receive NDP related events. As of this
change, only DAD related events are supported.
Tests: Existing tests were modified to use the NDPDispatcher's DAD events for
DAD tests where it needed to wait for DAD completing (failing and resolving).
PiperOrigin-RevId: 276338733
This change is in preparation for NDP Router Discovery where the stack will need
to handle NDP Router Advertisments.
Tests: Test that given an NDP Router Advertisement buffer (body of an ICMPv6
packet, correct values are returned by the field getters).
PiperOrigin-RevId: 276146817
This change makes sure that when an address which is already known by a NIC and
has kind = permanentExpired gets promoted to permanent, the new
PrimaryEndpointBehavior is respected.
PiperOrigin-RevId: 276136317
Right now, we send each tcp packet separately, we call one system
call per-packet. This patch allows to generate multiple tcp packets
and send them by sendmmsg.
The arguable part of this CL is a way how to handle multiple headers.
This CL adds the next field to the Prepandable buffer.
Nginx test results:
Server Software: nginx/1.15.9
Server Hostname: 10.138.0.2
Server Port: 8080
Document Path: /10m.txt
Document Length: 10485760 bytes
w/o gso:
Concurrency Level: 5
Time taken for tests: 5.491 seconds
Complete requests: 100
Failed requests: 0
Total transferred: 1048600200 bytes
HTML transferred: 1048576000 bytes
Requests per second: 18.21 [#/sec] (mean)
Time per request: 274.525 [ms] (mean)
Time per request: 54.905 [ms] (mean, across all concurrent requests)
Transfer rate: 186508.03 [Kbytes/sec] received
sw-gso:
Concurrency Level: 5
Time taken for tests: 3.852 seconds
Complete requests: 100
Failed requests: 0
Total transferred: 1048600200 bytes
HTML transferred: 1048576000 bytes
Requests per second: 25.96 [#/sec] (mean)
Time per request: 192.576 [ms] (mean)
Time per request: 38.515 [ms] (mean, across all concurrent requests)
Transfer rate: 265874.92 [Kbytes/sec] received
w/o gso:
$ ./tcp_benchmark --client --duration 15 --ideal
[SUM] 0.0-15.1 sec 2.20 GBytes 1.25 Gbits/sec
software gso:
$ tcp_benchmark --client --duration 15 --ideal --gso $((1<<16)) --swgso
[SUM] 0.0-15.1 sec 3.99 GBytes 2.26 Gbits/sec
PiperOrigin-RevId: 276112677
This change adds support for optionally auto-generating an IPv6 link-local
address based on the NIC's MAC Address on NIC enable.
Note, this change will not break existing uses of netstack as the default
configuration for the stack options is set in such a way that a link-local
address will not be auto-generated unless the stack is explicitly configured.
See `stack.Options` for more details. Specifically, see
`stack.Options.AutoGenIPv6LinkLocal`.
Tests: Tests to make sure that the IPb6 link-local address is only
auto-generated if the stack is specifically configured to do so. Also tests to
make sure that an auto-generated address goes through the DAD process.
PiperOrigin-RevId: 276059813
Like (AF_INET, SOCK_RAW) sockets, AF_PACKET sockets require CAP_NET_RAW. With
runsc, you'll need to pass `--net-raw=true` to enable them.
Binding isn't supported yet.
PiperOrigin-RevId: 275909366
It is quite legal to send from the ANY address (it is required for
DHCP). I can't figure out why the broadcast address was included here,
so removing that as well.
PiperOrigin-RevId: 275541954
NDP Neighbor Solicitations sent during Duplicate Address Detection must have an
IP hop limit of 255, as all NDP Neighbor Solicitations should have.
Test: Test that DAD messages have the IPv6 hop limit field set to 255.
PiperOrigin-RevId: 275321680
This change adds support for Duplicate Address Detection on IPv6 addresses
as defined by RFC 4862 section 5.4.
Note, this change will not break existing uses of netstack as the default
configuration for the stack options is set in such a way that DAD will not be
performed. See `stack.Options` and `stack.NDPConfigurations` for more details.
Tests: Tests to make sure that the DAD process properly resolves or fails.
That is, tests make sure that DAD resolves only if:
- No other node is performing DAD for the same address
- No other node owns the same address
PiperOrigin-RevId: 275189471
Reassembly can fail due to an invalid sequence of fragments
being received. eg. Multiple fragments with same id which
claim to be the last one by setting the more flag to 0 etc.
It's safer to just drop the reassembler and increment a metric
than to panic when reassembly fails.
PiperOrigin-RevId: 274920901
...and do not populate link address cache at dispatch. This partially
reverts 313c767b00, which caused malformed
packets (e.g. NDP Neighbor Adverts with incorrect hop limit values) to
populate the address cache. In particular, this masked a bug that was
introduced to the Neighbor Advert generation code in
7c1587e340.
PiperOrigin-RevId: 274865182
Netstack has its own stats, we use this to fill /proc/net/snmp.
Note that some metrics are not recorded in Netstack, which will be shown
as 0 in the proc file.
Signed-off-by: Jianfeng Tan <henry.tjf@antfin.com>
Change-Id: Ie0089184507d16f49bc0057b4b0482094417ebe1
Strengthen the header.IPv4.IsValid check to correctly check
for IHL/TotalLength fields. Also add a check to make sure
fragmentOffsets + size of the fragment do not cause a wrap
around for the end of the fragment.
PiperOrigin-RevId: 274049313
The behavior for sending and receiving local broadcast (255.255.255.255)
traffic is as follows:
Outgoing
--------
* A broadcast packet sent on a socket that is bound to an interface goes out
that interface
* A broadcast packet sent on an unbound socket follows the route table to
select the outgoing interface
+ if an explicit route entry exists for 255.255.255.255/32, use that one
+ else use the default route
* Broadcast packets are looped back and delivered following the rules for
incoming packets (see next). This is the same behavior as for multicast
packets, except that it cannot be disabled via sockopt.
Incoming
--------
* Sockets wishing to receive broadcast packets must bind to either INADDR_ANY
(0.0.0.0) or INADDR_BROADCAST (255.255.255.255). No other socket receives
broadcast packets.
* Broadcast packets are multiplexed to all sockets matching it. This is the
same behavior as for multicast packets.
* A socket can bind to 255.255.255.255:<port> and then receive its own
broadcast packets sent to 255.255.255.255:<port>
In addition, this change implicitly fixes an issue with multicast reception. If
two sockets want to receive a given multicast stream and one is bound to ANY
while the other is bound to the multicast address, only one of them will
receive the traffic.
PiperOrigin-RevId: 272792377
Kevin Krakauer
Bhasker Hariharan
Ghanan Gowripalan
Ian Gudger
gVisor bot
Andrei Vagin
Michael Pratt
Tamir Duberstein
Mithun Iyer
Jianfeng Tan
Chris Kuiper